Employees must not work on scaffold surfaces until
Jun 25, 2023 · Question: Employees must not work on scaffold surfaces until: A. It is determined to have strength and structural integrity to support intended loads . B. OSHA has visited the site and inspected the scaffold. C. The surface is completely dry. D. All of the above. Answer: A. Scaffolds shall not be moved horizontally while employees are on them, unless ... employee's work involving scaffolds indicate that the employee has not retained ...
Did you know?
Employees must not work on scaffold surfaces until: A. It is determined to have strength and structural integrity to support intended loads (correct answer) B. OSHA has visited the site and inspected the scaffold C. The surface is completely dry D. All of the above 11. From your choices below, what would you consider to be a "major" fall hazard ...٠٢/٠٤/٢٠١٣ ... Personnel working on scaffolds that are not completely enclosed by guardrails and midrails. • Workers erecting scaffolds and those who are ...The employee training requirements for ladder safety are also covered within 1910.30 Walking-Working Surfaces. If you’re an employer, it’s your responsibility to train your employees to use ladders safely. If an employee feels unsafe, they have the right to refuse work. The OSHA general industry ladder requirements can be summarized as follows:
Employees are not permitted to work on or from a scaffold during storms or high wind, unless a competent person has determined that it is safe, and those employees are protected by [29 CFR 1926.451(f)(12)]: Personal fall-arrest systems; Or wind screens (when windscreens are used the scaffold must be secured against the anticipated wind forces).15. All people, tools, materials, and loose objects must be removed from the scaffolding prior to moving it. 16. Ladders and other objects must not be used on the work platform to gain additional height. 17. Personnel shall not work from scaffolding during high winds (20 mph or more) or inclement weather. 1926.454 (a) The employer shall have each employee who performs work while on a scaffold trained [in] . . . 1926.454(a)(2) The correct procedures for dealing with . . .the fall protection systems being used . . . Link to standard 1926.451 at OSHA.gov; Part 1926, Subpart R 1926.760 - Steel Erection. 1926.760-Steel Erection 1926.760 Fall protectionThe employer must ensure: ( i) Each employee on a scaffold is protected from falling in accordance 29 CFR part 1926, subpart L; and. ( ii) Each employee using a rope descent system 4 feet (1.2 m) or more above a lower level is protected from falling by a personal fall arrest system. ( 13) Work on low-slope roofs.Employees must not work on scaffold surfaces until: A. The surfaces are determined to have the strength and structural integrity to support their intended ...
Get All Answers to OSHA 10 Construction Final Exam Careersafe osha 10 final exam answers. 10. Employees must not work on scaffold surfaces until: A. It is determined to have strength and structural integrity to support intended loads (correct answer) B. OSHA has visited the site and inspected the scaffold C Careersafe osha 10 final exam answersa fall hazard ( per OSHA) definitionis created whenever workers must climb onto trailers materials or equipment and their feet exceed ________ from the lower level or ground. 6 feet. OSHA requires fall protection when working near the edge of a trench or excavation that is ________ or more depth. 6 feet. ….
Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Employees must not work on scaffold surfaces until. Possible cause: Not clear employees must not work on scaffold surfaces until.
Employees must not work on scaffold surfaces until: A. The surfaces are determined to have the strength and structural integrity to support their intended loads (correct answer) B. OSHA has visited the site and inspected the scaffold . C. All surfaces are completely dry . D. All the above Access must be provided when the scaffold platforms are more than 2 feet (0.6 m) above or below a point of access. Direct access is acceptable when the scaffold is not more than 14 inches (36 centimeters) horizontally and not more than 24 inches (61 centimeters) vertically from the other surfaces. Cross braces shall not be used as a means of ...
the scaffold before each work shift. • If during the inspection a defect or damage to the scaffold is discovered, the scaffold must be tagged out and not used until repairs are made. Attach tags at the access point to the scaffold. One common tagging system uses the following tags: Red tag indicates: unsafe, do not use.What you need to do. A tower scaffold is one way to prevent a fall when working at height. The type of tower selected must be suitable for the work and erected and dismantled by people who have been trained and are competent to do so. Those using tower scaffolds should also be trained in the potential dangers and precautions required during use.1926.451 (b) (1) (i) Each platform unit (e.g., scaffold plank, fabricated plank, fabricated deck, or fabricated platform) shall be installed so that the space between adjacent units and the space between the platform and the uprights is no more than 1 inch (2.5 cm) wide, except where the employer can demonstrate that a wider space is necessary ...
black bear diner harker heights reviews The OSHA scaffolding safety procedures guide says it like this. Employers must provide fall protection for every employee on scaffolding more than 10 feet above a lower level. A competent person should determine the fall protection for employees working on supported scaffolds. Learn more about our OSHA Scaffold Competent Person Training today! meck mugshotsfire tv recast set up Employees must not work on scaffold surfaces until: A. The surfaces are determined to have the strength and structural integrity to support their intended loads (correct answer) B. OSHA has visited the site and inspected the scaffold C. All surfaces are completely dry D. All the above Access must be provided when the scaffold platforms are more than 2 feet (0.6 m) above or below a point of access. Direct access is acceptable when the scaffold is not more than 14 inches (36 centimeters) horizontally and not more than 24 inches (61 centimeters) vertically from the other surfaces. Cross braces shall not be used as a means of ... carle mychart login Employees must not work on scaffold surfaces until: A. It is determined to have strength and structural integrity to support intended loads B. OSHA has visited the site and inspected the scaffold C. The surface is completely dry D. All of the above sedanos weekly ad orlandohow much is 80000 penniescirrus 820 for sale "work platform" means an elevated or suspended temporary work surface used for supporting workers and includes a scaffold and boatswain's chair. Purpose of guideline The purpose of this guideline is to provide a chart to show the various types of work platforms covered by Part 13 of the Regulation , and a brief explanation of some types of ... zechar funeral home Select work locations that do not approach electrical power sources (e.g., power lines, transformers) by at least 10 feet and that do not pose other overhead hazards (e.g., other utilities, branches, overhangs, etc.). • If the job task requires work near an electrical source, the employer must ensure that the worker is324 (1) An employer must ensure that a single pole or double pole scaffold is. (a) supported against lateral movement by adequate bracing, (b) anchored by one tie‑in for each 4.6 metre vertical interval and one tie‑in for each 6.4 metre horizontal interval, (c) anchored by one tie‑in for each 3 metre vertical interval and one tie‑in for ... upap colorado springswhen blow nose ear squeaksnj pick 3 midday payout OSHA scaffolding rules recommend that your employees should not be working on wet and slippery surfaces. On scaffolding greater than a one inch, every employee should be wearing cleats, whch helps to preserve traction when walking over grating. All scaffolding stairways should also include slip resistant treads and landings on walk-able ... ٢٠/٠٢/٢٠٢٠ ... Each employee 4 feet or more above dangerous equipment must be protected from falling by: guardrail systems, safety net systems, travel ...